期刊


ISSN0268-3768
刊名The International Journal of Advanced Manufacturing Technology
参考译名先进制造技术国际杂志
收藏年代1998～2024



全部

1998 1999 2000 2001 2002 2003
2004 2005 2006 2007 2008 2009
2010 2011 2012 2013 2014 2015
2016 2017 2018 2019 2020 2021
2022 2023 2024

2009, vol.40, no.11-12 2009, vol.40, no.1-2 2009, vol.40, no.3-4 2009, vol.40, no.5-6 2009, vol.40, no.7-8 2009, vol.40, no.9-10
2009, vol.41, no.11-12 2009, vol.41, no.1-2 2009, vol.41, no.3-4 2009, vol.41, no.5-6 2009, vol.41, no.7-8 2009, vol.41, no.9-10
2009, vol.42, no.1/2 2009, vol.42, no.11/12 2009, vol.42, no.3/4 2009, vol.42, no.5/6 2009, vol.42, no.7/8 2009, vol.42, no.9/10
2009, vol.43, no.1/2 2009, vol.43, no.11/12 2009, vol.43, no.3/4 2009, vol.43, no.5/6 2009, vol.43, no.7/8 2009, vol.43, no.9/10
2009, vol.44, no.1/2 2009, vol.44, no.11/12 2009, vol.44, no.3/4 2009, vol.44, no.5/6 2009, vol.44, no.7/8 2009, vol.44, no.9/10
2009, vol.45, no.1/2 2009, vol.45, no.11/12 2009, vol.45, no.3/4 2009, vol.45, no.5/6 2009, vol.45, no.7/8 2009, vol.45, no.9/10

题名作者出版年年卷期
Complex nonlinear behaviors of drilling shaft system in boring and trepanning association deep hole drillingLingFei Kong; Yan Li; YanJun Lu; Dexin Li20092009, vol.45, no.3/4
Finite element simulation of earing defect in deep drawingRavindra K. Saxena; P. M. Dixit20092009, vol.45, no.3/4
Flange forming with combined blanking and extrusion process on sheet metals by FEM and experimentsC. H. Cao; L. Him; S. L. Liu20092009, vol.45, no.3/4
A case-based and practical approach for multivariate modeling of grinding processIndrajit Mukherjee; Pradip Kumar Ray20092009, vol.45, no.3/4
Research on thermal stress, deformation, and fatigue lifetime of the rapid heating cycle injection moldXiping Li; Guoqun Zhao; Yanjin Guan; Huiping Li20092009, vol.45, no.3/4
Application of PCA-based hybrid Taguchi method for correlated multicriteria optimization of submerged arc weld: a case studySaurav Datta; Goutam Nandi; Asish Bandyopadhyay; Pradip Kumar Pal20092009, vol.45, no.3/4
A linear piezo-electric ultrasonic motor using a single flexural vibrating bar for electro-discharge system industrial applicationsM. Shafik; E. M. Shehab; H. S. Abdalla20092009, vol.45, no.3/4
Development of an intelligent process model for EDMS. N. Joshi; S. S. Pande20092009, vol.45, no.3/4
Direct milling of polymethylmethacrylate for cranioplasty applicationsDalberto Dias da Costa; Helio Pedrini; Ovandir Bazan20092009, vol.45, no.3/4
An efficient approximate profiling method for the rack gear toolNicolae Oancea; Virgil Teodor; Ionut Popa; Victor Oancea20092009, vol.45, no.3/4
12



制造业外文文献服务平台